Springer Pumps, LLC.
Mailing: PO Box 269, Telford, PA 18969
Shipping: 861 Tech Drive, Telford, PA 18969

Int'l: 267-404-2910
Toll Free: 866-777-6060
Toll Free Fax: 866-777-6383
Email: info@springerpumps.com
Website: www.springerpumps.com
Print Back
The H-Series Gear Pumps were designed as an upgrade to Liquiflo®'s original 3-Series. With similar outside dimensions and capacities, the H-Series incorporates larger diameter shafts and bearings, allowing them to handle higher pressures with extended service life. H-Series pumps are available in Sealed and Mag-Drive versions with flows up to approximately 55 GPM and differential pressures up to 225 PSI with 300 PSI possible on some models.
  • Flows up to 55 GPM
  • Differential Pressures up to 225 PSI
  • Viscosities from 0.3 to 100,000+ cP
  • 316 SS or Alloy-C Basic Construction
  • Packing, Single Mechanical Seal, Double Mechanical Seal or Mag-Drive
  • Closed-Coupled or Long-Coupled
  • 12 Models Offered

Available Sealing Configurations

Magnetically Coupled (sealless): The magnetically coupled or mag-drive pump is the best method for handling toxic, noxious, crystallizing, or most other hazardous liquids since it completely contains the pumpage by isolating the drive shaft inside the pump housing. With no dynamic seal to leak or replace, the maintenance issues associated with seal leakage are eliminated. All Liquiflo® gear pumps are available with magnetic drive.

Mechanical Seal: Mechanical seals are offered in single and double configurations and are used for chemical applications where leakage needs to be minimized or eliminated. The single internal mechanical seal is the most common seal type and is ideal for pumping clean liquids up to 5,000 cP viscosity. The double mechanical seal requires a flushing system and is typically used when pumping liquids that are viscous, abrasive, crystalize on contact with air or are very hazardous. Carbon vs. SiC seal faces are the primary choice for most applications up to 500 °F. SiC vs. SiC seal faces have high abrasion resistance and can be applied up to 500 °F. Teflon vs. SiC seal faces have extreme chemical resistance and can be applied up to 180 °F and 50 PSI differential pressure.

Packing Seal: Packing is the simplest and most economical solution for pumping non-hazardous liquids where minor leakage is acceptable. Braided Teflon packing is the primary choice for applications up to 350 °F. Graphoil packing is available for high temperature applications up to 500 °F.



Available Options & Accessories


Replacement Cartridge: A cartridge is a complete mag-drive pump less the outer magnet and pedestal. A cartridge replacement is a convenient way to quickly replace a mag-drive pump that requires maintenance, ensuring maximum uptime.

Relief Valves: Positive displacement pumps should be installed with a relief valve in the discharge line to protect the pump and piping against any type of line blockage including the inadvertent closing of an isolation valve. Liquiflo® manufactures two sizes of relief valves in both 316 SS and Alloy-C.

Repair Kits: Repair Kits simplify inventory and speed repair. All parts can also be purchased separately. (See also Replacement Cartridge for even quicker repairs.)

Close-Coupled Configuration: All Liquiflo® gear pumps are available with the close-coupled configuration. This configuration simplifies installation and maintenance, and extends pump life by guaranteeing perfect pump-motor alignment.

Raised-Face Flanges: ANSI, DIN, and JIS Flanges are available to simplify piping connections and disconnections.

Sanitary Fittings: Tri-clamp sanitary fittings are a convenient alternative to threaded or flanged port connections.

S-Adapter: The S-Adapter is available for long-coupling mag-drive pumps; it isolates the pump from the motor and can be used when long-coupling pumps to motors or drives that do not have a C-face mounting. Maximum temperature rating is 250°F (120°C).

Power Frame: The Liquiflo® Power Frame is used for long-coupling mag-drive pumps that are used for high temperature applications, up to the pump's maximum temperature rating. Its integral cooling jacket keeps the bearing system of the pedestal cool even when it is coupled to a pump operating at extremely high temperature.

Clamp-On Temperature Control Jacket: Temperature Control Jackets can maintain the pump at either elevated or reduced temperatures. They are commonly used when pumping liquids that solidify or become difficult to pump when the temperature decreases.

Dual-Kan™: Liquiflo®'s patented Dual Kan controls the back-end temperature of a mag-drive pump by circulating a heating or a cooling fluid through the containment can. This is ideal for applications requiring precise and uniform temperature control.

Base Plate Mounting: Liquiflo® gear pumps are available with base-mounts to simplify installation. Liquiflo® also offers base-mounts with or without the motor pre-installed.

Hard-Coated Shafts: Hard-coated shafts are used to extend pump life in difficult applications requiring higher levels of wear resistance. Ceramic Chrome Oxide (CO) and Tungsten Carbide (TC) coatings are available.

Accessories & Spare Parts: Mechanical couplings, coupling guards, risers, base plates, adapters, brackets, pedestals and individual pump components can all be purchased separately.

Liquiflo H Series H1-H9 Sealed Close Coupled
Unit of Measure
Items Liquiflo H Series H1-H9 Mag-Drive Close Coupled
LF-H1F
Liquiflo H1F Heavy Duty Industrial Gear Pump
Price QUOTE
Liquiflo H Series H1-H9 Mag-Drive Close Coupled
LF-H3F
Liquiflo H3F Heavy Duty Industrial Gear Pump
Price QUOTE
Liquiflo H Series H1-H9 Mag-Drive Close Coupled
LF-H5R
Liquiflo H5R Heavy Duty Industrial Gear Pump
Price QUOTE
Liquiflo H Series H1-H9 Mag-Drive Close Coupled
LF-H5F
Liquiflo H5F Heavy Duty Industrial Gear Pump
Price QUOTE
Liquiflo H Series H1-H9 Mag-Drive Close Coupled
LF-H7N
Liquiflo H7N Heavy Duty Industrial Gear Pump
Price QUOTE
Max. Flow Rate N/A 0.5 gpm1.9 lpm N/A 1.4 gpm5.30 lpm N/A 2.4 gpm9.08 lpm N/A 3.4 gpm12.87 lpm N/A 5.4 gpm20.44 lpm
Discharge Pressure N/A 20.7 bar300 psi N/A 20.7 bar300 psi N/A 20.7 bar300 psi N/A 20.7 bar300 psi N/A 15.5 bar225 psi
Max. Viscosity N/A 100000 cps
Max. Speed N/A 1750 rpm
Port Connections N/A 0.25" BSPT 0.25" NPT 0.5" 150# ANSI Flange DIN 10 PN16 Flange N/A 0.25" BSPT 0.25" NPT 0.5" 150# ANSI Flange DIN 10 PN16 Flange N/A 0.5" 150# Flange 0.5" BSPT 0.5" NPT DIN 15 PN16 Flange N/A 0.5 150# RF Flange 0.5 BSPT 0.5 NPT DIN 15 PN16 RF Flange N/A 0.75" 150# ANSI Flange 0.75" BSPT 0.75" NPT DIN 20 PN16 Flange
Max. Fluid Temperature N/A 500 ºF260 ºC
Self-Priming N/A 0.5 ft N/A 1.5 ft N/A 2.0 ft N/A 4.0 ft N/A 6.0 ft