Think Pumps – Think SpringerPhone: 866-777-6060||
Search
Menu
  • Product Image - Pump N Mixer

    Three Operations
    Mixing, Pumping Only or Mixing & Pumping Simultaneously
    The FLUX Pump-N-Mixer allows you to either pump, mix, or pump and mix simultaneously.

    The F426 eliminates the need for a separate drum mixer when the contents of the container must be thoroughly mixed before they can be pumped out. Both mixing and pumping can be performed with the same unit, the FLUX unique lever action design allows the user to perform several functions with the turn of a lever.

    This unit is available in Stainless Steel and also Polypropylene, and can be used with any of the FLUX motors subject to application.

    Note: When using the drum pump as a mixing pump there is a risk-as in all circulation operations with electrically non-conductive liquids-that the circulated liquid (especially when it contains a high percentage of non-dissolved solid or liquid particles in suspension) will be charged electrostatically.

    Please make sure that any ignition risk will be eliminated before commencing mixing operation.

  • 314-43-007
  • 417-40-010

    """"Acids and Alkalis""""
    for transferring acids and alkalis like ammonia water, hydrofluoric acid (diluted), fruit acids, phosphoric acid, hydrochloric acid and liquid fertilizers.

    Motor
    Commutator motor F 417, 230 Volt, 50 Hz, 450 Watt, IP 24 with 5 m power supply cable and 2-pole plug

  • 458-60-010

    """"Concentrated Acids and Alkalis""""
    for transferring concentrated acids like chloric acid, chromic acid, hydrobromic acid, hydrofluoric acid, nitric acid, sulphuric acid and sodium hypochlorate

    Motor
    Commutator motor F 458, 230 Volt, 50 Hz, 460 Watt, IP 55 with special corrosion-resistant painting, 5 m power supply cable and safety plug

  • 457-10-010
  • 416-24-010
  • 416-20-010
  • 416-25-010
  • fmc100

    Flux Liquid Meter Type FMC 100
    If you want to keep your liquids under control, FLUX Pump Kits can be completed by a Liquid Meter Type FMC 100. 3 models are available in PP, ETFE or stainless steel for flowates of 10 - 100 l/min. An easy-to-read 7-digit LCD together with multifunctional keys ensures a simple calibration and input, everything for easy use by the operator. All models are explosion-proof to II 2 G EEx ia IIB T6 according to Directive 94/9/EC-ATEX 100. For detailed information and part numbers please refer to our catalogue FLUX LIQUID METER TYPE FMC, which is available on simple request.

  • 450

    Flux Eccentric Worm-Drive Pump Type F 550 GS
    If it comes to more viscous fluids - FLUX Eccentric worm-drive pump Type F 550 GS. Lightweight, portable barrel pump in stainless steel with planetary gear for transferring paints, varnishes, oils, detergents, soaps, shampoos, fruit juices, jams, syrups, etc. Delivery rate up to 50 l/min, delivery head up to 8 bar, viscosity up to 30.000 mPas (cP), temperature up to 150 ºC. With electric or compressed air motor. Detailed information, also on further models, can be seen in our catalogue FLUX HIGH VISCOSITY LIQUID PUMPS, which is available on simple request.

  • Product Image - F424

    "In Good Contact with the Liquids"
    The liquids to be pumped are abrasive, but they do not leave any deposits. Dry running of the pump must not cause any problems. You are looking for a general purpose pump without a mechanical seal in the liquid section. The O-ring material FKM is not resistant to the liquids to be pumped.

    The inner tube supports the pump shaft, which is lubricated by the liquid. The level of the liquid in the inner tube always corresponds to that in the drum or container.

  • F430

    "A Shaft in a Shell"
    The pump must be used with many varying liquids, consequently the smallest residual left within the pump is unacceptable. You want to pump adhesive substances like paints, or liquids which tend to crystallize or harden.

    The inner tube houses the shaft. It is sealed at the bottom by mechanical seal through which the shaft passes. Consequently the shaft does not come into contact with the liquid except for the small section between the impeller and seal.

  • F425

    "Perfection in Drum Emptying"
    You are not prepared to accept any residual liquid in the drum in order to avoid problems and costs of disposal or to avoid losing high value liquids.

    Before the motor is switched off, the flowback stop valve at the pump inlet must be closed by operating the lever. This prevents the liquid flowing back into the empty drum.

  • F426

    "An Excellent Mixture"
    You want to mix and pump liquids within a closed drum or an open container.
    By turning the adjusting lever, the pump can either mix or pump. Liquids can also be mixed even when being transferred to another container.

  • F427

    "Pure Culture in Pumping"
    You want a safe pumping of food, cosmetic or pharmaceutical products. The operating conditions require an easy and quick cleaning or sterilization of the pump at regular intervals to avoid any contamination of the product, e.g. when pumping varying liquids or different colors as well as quick-drying or film forming liquids.

    The efficient FLUX sanitary pump has been especially designed for aseptic applications.

  • cat
  • Product Image - F425

    Operation and Function of Flux Pump Tubeset F425
    When emptying a drum or container, the liquid which remains in the pump tubeset or hose being used with a Flux hand nozzle will always remain under the control of the operator. The pump tubeset-model F425-is equipped with an integrated back-flow stop in the lower part of the pump housing, which is operated manually by turning an adjustable lever 90 degrees to a locked position. As soon as the drum or container is completely empty and no more liquid is being discharged, the integrated back-flow stop must be closed with the motor still running. (In that way, any back-flow of the liquid is prevented and ensures that the drum or container is emptied to its maximum.)

    Advantages of Flux Tubeset F425

    • Drums and containers can be emptied in vertical position up to one (1) pint and in tilted position up to 3 oz. residual quantity.
    • By closing the back-flow stop at the bottom of the tubeset, the liquid in the pump and transfer hose cannot flow back into the drum or container.
    • Pump tubeset F425 S in stainless steel has an outer diameter of only 1 19/32 in. over the total effective immersion length, F425 Pouter diameter is 2 in.
    • No loss of liquid or environmental problems with remaining liquid in drums and containers. No contamination of environment due to leaking liquid.
    • Easy to operate, easy to dismantle and service with cleaning a simple operation.

  • FLUX MiniFLUX

    The MINIFLUX horizontally installed container pump is designed for emptying IBCs via their floor-level outlet. Designed as an alternative to a vertical pump, the MINIFLUX can be used when an IBC is not accessible from the top. It is suitable for applications when gravity draining via the outlet tap is insufficient eg. rapid dispensing, long distance product transfer, or transfer to another container in a higher location. Power can ideally be provided by commutator or compressed air motor.


    Features & Benefits:

    • Easy to use
    • Eliminates lifting tote and splashing of harmful liquids
    • Extended service life through proven seal design
    • Flows to 63 GPM
    • Heads to 43 feet
    • Viscosities to 1,000 cPs
    • XP rated

  • F-550-S

    Recommended for transferring
    Thin to high viscosity, even pasty, still free flowing substances.

    Seal Types
    Type F 550 S with mechanical seal or Type F 550 SB with stuffing box.

    Available Drive Motors
    Three-phase electric or compressed air motors. Three-phase motors of 0.75 or 1.1 kW, with a speed of 930 or 700 rpm. For high viscosity, pasty substances a motor of 1.1 kW is required with a recommended speed of 700 rpm for viscosities exceeding 50.000 mPas (cP), because of the low velocity of such products. A speed of 930 rpm may be used if the product is still flowing or if a follow-on plate would support the continuous flow of the product to the pump inlet.
    For viscosities up to 25.000 mPas (cP) a motor of 0.75 kW and 930 rpm will be sufficient.
    On compressed air motors of 0.5 to 1.8 kW, the speed may be controlled by a valve in the air supply line.
    With higher viscosities delivery rate will be lower, depending on the velocity of the fluid.
    Values ±10% at 930 rpm. Delivery rate depends on the velocity of the fluid.

    Scope of Supply
    A complete eccentric worm-drive pump consists of: drive motor, pump, stator and hose connection.

  • F-560-S

    Recommended for transferring
    Thin to high viscosity, even pasty, still free flowing substances.

    Seal type
    Mechanical seal

    Available drive motors
    Three-phase electric motors or compressed air motors

    Scope of supply
    A complete eccentric worm-drive pump consists of: drive motor, pump, stator and hose connection.
    With higher viscosities delivery rate will be lower, depending on the velocity of the fluid.
    Values ±10% at 930 rpm. Delivery rate depends on the velocity of the fluid.

  • Product Image

    Recommended for transferring
    Thin to high viscosity, even pasty, still free flowing substances.

    Seal type
    Mechanical seal

    Available drive motors
    Three-phase electric motors

    Scope of supply
    A complete horizontal pump consists of: drive motor, pump and stator, hose connection on inlet and outlet, base plate.

  • F-550-GS

    Recommended for transferring
    Thin to medium viscosity liquids up to a maximum viscosity of 30.000 mPas (cP).

    Seal type
    Type F 550 GS with mechanical seal or Type F 550 GSB with stuffing box

    Available drive motors
    Commutator motors or compressed air motors.
    An infinitely variable speed variator - also available on explosion-proof models - allows the operator to set pump capacity to specific delivery requirements.

    Scope of supply
    A complete eccentric worm-drive pump consists of: drive motor, pump, stator and hose connection.

  • F-560-GS3A-54

    Recommended for transferring
    Thin to medium viscosity liquids up to maximum 30.000 mPas (cP).

    Seal type
    Mechanical seal

    Available drive motors
    Commutator motors or compressed air motors. An infinite variable speed variator - also on explosion-proof motors - allows the operator to set pump capacity to specific delivery requirements.

    Scope of supply
    A complete sanitary pump consists of: drive motor, pump, stator and hose connection.

  • F-550-GS6-50

    Recommended for transferring
    Thin to high viscosity substances up to a maximum viscosity of 80,000 mPas (cP).

    Seal type
    Mechanical seal (stuffing box on request).

    Available drive motors
    Single-phase AC motors with capacitor switch or three-phase motors.

    Scope of supply
    A complete eccentric worm-drive pump consists of: drive motor, pump, stator and hose connection.
    Eccentric worm-drive pumps type F 550 GS6 with planetary gear, without drive motor

  • F520s-cat

    Recommended for transferring
    Low to medium viscosity liquids up to a maximum viscosity of 20.000 mPas (cP).

    Seal type
    Mechanical seal

    Available drive motors
    Three-phase electric motors or compressed air motors

    Scope of supply
    A complete screw pump consists of: drive motor, pump and hose connection.
    Screw pumps F 520 S, without drive motor

  • pumpacce
  • drv

    Drive motors for eccentric worm-drive pumps type F 550 S and sanitary pumps type F 560 S version with bearing flange

  • Drive-prod

    Drive motors for eccentric worm-drive pumps type F 550 GS and sanitary pumps type F 560 GS version with planetary gear

  • Product Image - High Viscosity Liquid Pump F520S

    The F520S is a rotary screw pump. The pump is capable of handling fluids with viscosities to 25000 cP. The rotary screw design produces a smooth non-pulsating flow making it an excellent choice for pumping oils. Both pneumatic and electric drives are available.

  • Product Image - Positive Displacement Pump F550S

    The Flux F550S is a direct drive progressive cavity pump. The progressive cavity design produces a smooth flow of product with very little product degradation. The direct drive version allows the use of higher horsepower motors enabling the pump to handle viscosities in excess of 100000 cP. Applications include, but are not limited to, polymers, resins, adhesives, silicones and oils. Both pneumatic and electric motors are available.

  • Product Image - Positive Displacement Pump F55GS

    The Flux F55GS is a gear drive progressive cavity pump. The progressive cavity design produces a smooth flow of product with very little product degradation. The gear drive version allows the use of most Flux F400 series motors. This pump is capable of handling viscosities to 50000 cP. Applications include, but are not limited to, polymers, resins, adhesives, and oils. Both pneumatic and electric motors are available.

  • Item Image - F460-1 EX
  • FLUX JUNIORFLUX SS Tube

    The small drum pump JUNIORFLUX with its fixed collector motor is available with a mechanical seal (F 310) and as a sealless version (F 314). It is especially suitable for pumping comparably small quantities out of containers such as canisters or drums of up to 200 litres. The small outer tube diameter allows pumping even out of narrow openings.

  • FLUX COMBIFLUX PVDF Tube

    The small, sealless drum pump COMBIFLUX FP 314 can be use with the collector motor FEM 3070 (with mains connection) or the new battery motor FBM-B 3100, the world's first maintenance-free battery motor for pumps. It is of a modular design, so that several pumps can be operated in with one motor. Like the JUNIORFLUX , the COMBIFLUX is especially suitable for pumping comparably small quantities out of containers such as canisters or drums of up to 55 gallons. The small outer tube diameter allows pumping even out of narrow openings.


    View the COMBIFLUX Drum Pump Video HERE

^