Think Pumps ~ Think SpringerPhone: 866-777-6060||
Search
Menu

The 3-Series Gear Pumps have been replaced by the H-Series gear pump line. The H-Series is recommended for all new applications as well as an upgrade to any existing 3-Series installations.

Liquiflo's original 3-Series Gear Pumps are available in Sealed and Mag Drive versions with flows up to approximately 55 GPM and differential pressures up to 100 PSI.
  • Flows up to 55 GPM
  • Pressures up to 100 PSI
  • 316 SS, Alloy-C or Alloy-20
  • 11 Models Offered

Available Sealing Configurations

Magnetically Coupled (sealless): The magnetically coupled or mag-drive pump is the best method for handling toxic, noxious, crystallizing, or most other hazardous liquids since it completely contains the pumpage by isolating the drive shaft inside the pump housing. With no dynamic seal to leak or replace, the maintenance issues associated with seal leakage are eliminated. All Liquiflo gear pumps are available with magnetic drive.

Mechanical Seal: Mechanical seals are offered in single and double configurations and are used for chemical applications where leakage needs to be minimized or eliminated. The single internal mechanical seal is the most common seal type and is ideal for pumping clean liquids up to 5,000 cP viscosity. The double mechanical seal requires a flushing system and is typically used when pumping liquids that are viscous, abrasive, crystalize on contact with air or are very hazardous. Carbon vs. SiC seal faces are the primary choice for most applications up to 500 °F. SiC vs. SiC seal faces have high abrasion resistance and can be applied up to 500 °F. Teflon vs. SiC seal faces have extreme chemical resistance and can be applied up to 180 °F and 50 PSI differential pressure.

Packing Seal: Packing is the simplest and most economical solution for pumping non-hazardous liquids where minor leakage is acceptable. Braided Teflon packing is the primary choice for applications up to 350 °F. Graphoil packing is available for high temperature applications up to 500 °F.



Available Options & Accessories


Replacement Cartridge: A cartridge is a complete mag-drive pump less the outer magnet and pedestal. A cartridge replacement is a convenient way to quickly replace a mag-drive pump that requires maintenance, ensuring maximum uptime.

Relief Valves: Positive displacement pumps should be installed with a relief valve in the discharge line to protect the pump and piping against any type of line blockage including the inadvertent closing of an isolation valve. Liquiflo manufactures two sizes of relief valves in both 316 SS and Alloy-C.

Repair Kits: Repair Kits simplify inventory and speed repair. All parts can also be purchased separately. (See also Replacement Cartridge for even quicker repairs.)

Close-Coupled Configuration: All Liquiflo gear pumps are available with the close-coupled configuration. This configuration simplifies installation and maintenance, and extends pump life by guaranteeing perfect pump-motor alignment.

Raised-Face Flanges: ANSI, DIN, and JIS Flanges are available to simplify piping connections and disconnections.

Sanitary Fittings: Tri-clamp sanitary fittings are a convenient alternative to threaded or flanged port connections.

S-Adapter: The S-Adapter is available for long-coupling mag-drive pumps; it isolates the pump from the motor and can be used when long-coupling pumps to motors or drives that do not have a C-face mounting. Maximum temperature rating is 250°F (120°C).

Power Frame: The Liquiflo Power Frame is used for long-coupling mag-drive pumps that are used for high temperature applications, up to the pump's maximum temperature rating. Its integral cooling jacket keeps the bearing system of the pedestal cool even when it is coupled to a pump operating at extremely high temperature.

Clamp-On Temperature Control Jacket: Temperature Control Jackets can maintain the pump at either elevated or reduced temperatures. They are commonly used when pumping liquids that solidify or become difficult to pump when the temperature decreases.

Dual-Kan™: Liquiflo's patented Dual Kan controls the back-end temperature of a mag-drive pump by circulating a heating or a cooling fluid through the containment can. This is ideal for applications requiring precise and uniform temperature control.

Base Plate Mounting: Liquiflo gear pumps are available with base-mounts to simplify installation. Liquiflo also offers base-mounts with or without the motor pre-installed.

Hard-Coated Shafts: Hard-coated shafts are used to extend pump life in difficult applications requiring higher levels of wear resistance. Ceramic Chrome Oxide (CO) and Tungsten Carbide (TC) coatings are available.

Accessories & Spare Parts: Mechanical couplings, coupling guards, risers, base plates, adapters, brackets, pedestals and individual pump components can all be purchased separately.

1 - 11 of 11 | Results Per Page | View | Unit of Measure
1 

Item #

Price

Max. Flow Rate

Discharge Pressure

Curve Image

Max. Viscosity

Max. Speed

Port Connections

Max. Fluid Temperature

Self-Priming

Add To Cart/Request Quote
LF-31F QUOTE N/A 0.5 gpm1.9 lpm N/A 20.7 bar300 psi N/A N/A 100000 cps N/A 1750 rpm N/A 0.25" BSPT 0.25" NPT 0.5" 150# ANSI Flange DIN 10 PN16 Flange N/A 500 ºF260 ºC N/A 0.5 ft Add To Cart
Request Quote
LF-33F QUOTE N/A 1.4 gpm5.3 lpm N/A 20.7 bar300 psi N/A N/A 100000 cps N/A 1750 rpm N/A 0.25" BSPT 0.25" NPT 0.5" 150# ANSI Flange DIN 10 PN16 Flange N/A 500 ºF260 ºC N/A 1.5 ft Add To Cart
Request Quote
LF-35R QUOTE N/A 2.4 gpm9.1 lpm N/A 20.7 bar300 psi N/A N/A 100000 cps N/A 1750 rpm N/A 0.5" 150# ANSI Flange 0.5" BSPT 0.5" NPT DIN 15 PN16 Flange N/A 500 ºF260 ºC N/A 2.0 ft Add To Cart
Request Quote
LF-35F QUOTE N/A 3.4 gpm12.9 lpm N/A 20.7 bar300 psi N/A N/A 100000 cps N/A 1750 rpm N/A 0.5" 150# ANSI Flange 0.5" BSPT 0.5" NPT DIN 15 PN16 Flange N/A 500 ºF260 ºC N/A 4.0 ft Add To Cart
Request Quote
LF-37R QUOTE N/A 8.6 gpm32.5 lpm N/A 15.5 bar225 psi N/A N/A 100000 cps N/A 1750 rpm N/A 0.75" 150# ANSI Flange 0.75" BSPT 0.75" NPT DIN 20 PN16 Flange N/A 500 ºF260 ºC N/A 6.0 ft Add To Cart
Request Quote
LF-37F QUOTE N/A 10.7 gpm40.4 lpm N/A 15.5 bar225 psi N/A N/A 100000 cps N/A 1750 rpm N/A 0.75" 150# ANSI Flange 0.75" BSPT 0.75" NPT DIN 20 PN16 Flange N/A 500 ºF260 ºC N/A 7.0 ft Add To Cart
Request Quote
LF-39R QUOTE N/A 15 gpm56.7 lpm N/A 15.5 bar225 psi N/A N/A 100000 cps N/A 1750 rpm N/A 1" 150# ANSI Flange 1" BSPT 1" NPT DIN 25 PN16 Flange N/A 500 ºF260 ºC N/A 6.0 ft Add To Cart
Request Quote
LF-39F QUOTE N/A 21.5 gpm81.3 lpm N/A 15.5 bar225 psi N/A N/A 100000 cps N/A 1750 rpm N/A 1.25" 150# ANSI Flange 1.25" BSPT 1.25" NPT DIN 32 PN16 Flange N/A 500 ºF260 ºC N/A 14.0 ft Add To Cart
Request Quote
LF-312R QUOTE N/A 22 gpm83.2 lpm N/A 18.6 bar270 psi N/A N/A 100000 cps N/A 1150 rpm N/A 1.25" BSPT 1.25" NPT 1.5" 150# ANSI Flange DIN 40 PN16 Flange N/A 500 ºF260 ºC N/A 15.0 ft Add To Cart
Request Quote
LF-312F QUOTE N/A 29 gpm109.6 lpm N/A 18.6 bar270 psi N/A N/A 100000 cps N/A 1150 rpm N/A 1.25" BSPT 1.25" NPT 1.5" 150# ANSI Flange DIN 40 PN16 Flange N/A 500 ºF260 ºC N/A 17.0 ft Add To Cart
Request Quote
LF-314F QUOTE N/A 58 gpm219.2 lpm N/A 18.6 bar270 psi N/A N/A 100000 cps N/A 1150 rpm N/A 2.5" 150# ANSI Flange DIN 65 PN16 Flange N/A 500 ºF260 ºC N/A 20.0 ft Add To Cart
Request Quote
1 - 11 of 11 | Results Per Page | View | Unit of Measure
1 
^